How To Install A Reverse Camera As A Rear View

Download Article

A rear-view camera, also known equally a fill-in camera, lets you see what's backside your vehicle without having to await backwards. Though the device comes standard with many new motorcar models, yous can add together a rear-view photographic camera to your vehicle if it didn't come with i.

1
Buy a mountable backup photographic camera for your specific vehicle. For safety, make sure yous purchase a device specifically designed to be a rear-view camera. Purchasing 1 fabricated for your specific vehicle volition make it easier to install than a standard aftermarket photographic camera. So you can install it easily, look for a camera that mounts onto or directly behind your license plate.^[1]
- Wait for backup cameras at consumer electronics stores.
2
Become an external monitor if you want to keep your existing rear-view mirror. An external backup monitor is a small video screen that mounts onto your windshield similarly to a GPS. Though they have upwardly more space than internal monitors, external monitors are far easier to see and can be hands replaced if necessary.
- If you'd like, you can use a standard video monitor instead. Notwithstanding, keep in mind that it may non have all the same features as devices designed for use with backup cameras.
Ad
3
Purchase an internal monitor for a less obtrusive device. An internal backup monitor is a fully functioning rear-view mirror that houses a minor screen inside the glass. Some internal monitors clip on superlative of your current rear-view mirror, but others replace your original mirror entirely.^[two]
- Most internal monitors close off and disappear when not in use, making them a perfect option if you desire to preserve your car's looks.
iv
Buy ability and video cords if your photographic camera and monitor didn't include them. For most rear-view camera installations, you'll need camera and monitor splitter cords with connectors for video and ability cables, ii blank wire power cables, and an RCA video cable.^[3]
- Near installation kits include these cables, simply some may require you to buy them separately.
- Some camera models use wireless transmitters instead of standard video cables.
Advertisement

1
Take off your rear license plate. Using a Phillips head screwdriver, remove each of the screws belongings your rear license plate in place. Then, pull the plate off and set it bated.^[iv]
- Make sure you place the screws in a rubber place and so you don't lose them.
two
Remove your body's interior panel. Pop open your trunk and expect for a solid interior console covering the opposite side of your license plate mounting area. Then, insert a trim removal tool or other thin device backside the panel and pry it off.^[5]
- Removing this panel will expose the car's rear wiring chambers.
3
Drill a minor hole in the license plate mounting area. Make sure there are no obstructions betwixt the license plate mountain and the rear wiring chamber. Then, create a small hole in the car using a ability drill equipped with a high-speed twist drill bit. Line up your hole so it is directly backside where your camera's power and video cable volition get.^[6]
- To figure out where to make the hole, concord your camera up to the expanse you intend to mount it. Then, notation the spot where its splitting string sits.
- Create a hole that'southward large enough to fit your camera's power and video cable.
- If yous come across any obstructions, endeavor to remove them. If you tin't, come across if you can make a pigsty nearby.
- For most jobs, y'all'll need a drill bit that has a diameter betwixt ^ane⁄_eight and ^ane⁄₄ in (0.32 and 0.64 cm).
4
Place a safety grommet around your camera cable. Before running your camera cablevision into the car, slip a rubber grommet onto it near the non-splitting terminate. These small rubber washers, available at most home improvement stores, will keep the wire in place and forbid leaks.^[seven]
- Cull a grommet that's simply large enough to fit within the drilled hole.
5
Run the camera cable into your body. Pull the splitting cease of your photographic camera's video and power cable through the drilled hole into the trunk of your auto. Make sure you pull it tight so the rubber grommet lodges into the drilled hole.
- Your camera cable should run from the outside of the car to the inside of the auto.
half dozen
Locate your automobile's two reverse low-cal wires. Opposite lite wires are the cords that connect your car's tail lights to the dashboard. They hook directly into your vehicle'south tail lights and are usually located in the hatch or trunk of your machine.
- These cords await different for every vehicle then, if you can't observe them, consult your owner's manual for model specific information.
seven
Strip and dissever your car's reverse low-cal wires. Using a wire stripper or pliers, pare back the rubber covering the wires. So, utilise a screwdriver or other thin tool to poke a hole through the eye of each exposed wire, separating the private wire strands.^[8]
- For condom, make sure you do this while the car is turned off.
eight
Fuse your camera wires with the opposite light wires. Attach 1 of your blank wire cables to the camera cord's power connector. Then, poke your blank wires through the eye of the exposed reverse low-cal wires and twist them together. For condom, make sure you lot wrap the combined wires in electrical tape.^[9]
- Make sure you poke your positive (usually red) bare wire through the positive reverse light wire and the negative (usually black) bare wire through the negative reverse light wire.
Advertising

ane
Route your camera's video cable to the front of the car. Connect your RCA cablevision to the camera string'due south video connector if necessary. And so, run information technology through your vehicle to the area by the fuse box. Depending on your vehicle model, you'll commonly be able to do this by peeling back the auto'southward headliner or side panels and pulling your cable through the exposed bedroom.^[10]
- For certain trucks, y'all may need to run the video cable through the vehicle's frame rail.
- In most cars, you'll find the fuse box underneath the steering cycle.
ii
Fix external monitors to the front windshield. If you're installing an external monitor, starting time attach your device's included mountain to the windshield by following the manufacturer'southward included instructions. Then, hook your monitor onto the mountain.
- Almost external monitors employ a suction mountain, though others may come with a more complex mounting system.
3
Attach internal monitors to the rear-view mirror or mirror mount. For certain internal monitors, you'll need to clip the new device onto your current rear-view mirror. For others, yous'll need to take off the mirror and slide your monitor into the pre-existing mirror mount.^[11]
- Some internal monitors may come with their own mounting system that you'll have to attach to the car'due south front windshield.
four
Run the monitor's splitter cable to the fuse box. If necessary, hook your monitor's ability and video cablevision into the device. Then, route the cablevision from the monitor to the area side by side to the fuse box.^[12]
- If you'd similar, use a trim removal tool to pop out the headlining panel straight above your windshield. Then, run your cablevision through the exposed sleeping accommodation.
v
Connect your monitor'due south camera cable to the RCA cablevision. Afterwards routing your monitor's splitter cable, connect the video end of the cable to your camera's RCA cord. So, wrap the connected cords with electrical tape to hold them together.
- If your RCA and video cables have the same ends, y'all may need to purchase an RCA male to female converter cord. You tin notice these at most electronic stores.
half dozen
Attach your monitor'south power cable to a fuse tap. Connect your remaining bare wire cablevision to the fill-in monitor'south power cord. Then, push the positive (usually cherry) end of the bare wire cable into the open end of a fuse tap. Finally, crimp the two cables together with a pair of pliers.^[13]
- A fuse tap is a small-scale cable that converts a bare wire into a fuse point. You tin can notice them at most car part stores.
- If y'all'd adopt, y'all can leave the bare wire cable off and connect your camera'south ability cable to a cigarette lighter adaptor. Then, plug this adaptor into your car'southward cigarette lighter receptacle for power.
7
Plug the fuse tap into the fuse box. Locate your fuse box and open it up. Then, plug your fuse tap into an open fuse prison cell. If necessary, cheque your fuse box'south lid or your vehicle's didactics manual to see which slots are open.^[14]
- After attaching your fuse, consider taping all your wires together using electrical tape to become them out of the way.
Advertisement

1
Connect your backup camera to its power and video cable. Return to the back of your car once you lot've installed the rear-view monitor and all the necessary camera cords. Close the trunk if necessary, and so connect the backup photographic camera to its power and video cable.
- Your camera'south power and video cable should be sticking out of the pigsty you drilled in the license plate mounting area.
2
Mount the camera to your license plate. If the camera attaches to the front of your license plate, fix it to the plate past following the manufacturer's included instructions. If the camera attaches to the back of your license plate, line the device up with the plate'due south fastener holes and thread screws through them.^[15]
- In well-nigh cases, you can adhere a rear-view camera to the back of your license plate using the screws you removed from the car earlier.
3
Reattach your license plate and trim panels. Using a Phillips head screwdriver, put your rear license plate back on your vehicle. One time you've reattached information technology, give the license plate and backup camera firm tugs to brand sure they're secure.
- If you haven't already, reattach your car'southward interior trunk console and other trim panels past pressing them back onto the vehicle.
4
Examination the camera to make sure everything works. Before using your new camera on public roads, test it in a prophylactic area like your driveway. If it turns on, identify a big, durable object like a trash can behind the camera to see how distorted the image is. If information technology does not plow on, read your installation manual for troubleshooting information.
- In many cases, rear-view camera malfunctions are caused by loose or improperly connected wires.
Advertizement

Add New Question

Question

I hooked the photographic camera upward and information technology merely flickers. Whatsoever communication?

Yous may want to ensure all cables and connections are secured tightly. Double bank check that all connections are correct. If this doesn't work, check to encounter if the camera chosen is in expert shape and isn't physically damaged.
Question

Suzuki installed reverse parking camera in my Swift Dzire Zxi. But the photographic camera shows upper view and non the ground below. What can I do ?

Make sure that the photographic camera is installed the right manner (not upside downwardly), and check the position of the photographic camera mounted. Take it back to the dealer that installed it and enquire them to check the alignment and fit.
Question

What is the best acme for a reversing photographic camera?

There is no optimal height for a back-upwardly camera. The ideal height is based off the specific car or vehicle that y'all have and your personal preferences, forth with its intended application. Some redundancy cameras are placed on big service trucks so that they can line up to trailer hitches easier, some are to prevent a blindspot on the road. Depending on your application, information technology can be placed at any height. Nigh reversing cameras are a "wide view" style and the specific peak location does non always impact the way it functions.

Enquire a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Though nigh car dealers and mechanics will not install aftermarket backup photographic camera systems, many audio and electronic shops volition.

Advertising

Brand certain you plow the car off before working with blank or stripped wires. If y'all need to touch exposed wires while the car is on, put on a pair of shock-resistant rubber gloves.

Things You'll Demand

Rear-view camera
Rear-view monitor
Connector cables
Phillips head screwdriver
Trim removal tool
Power drill with high-speed twist scrap
Condom grommet
Wire stripper or pliers
Electrical tape
Fuse tap

About This Article

Commodity Summary Ten

To successfully install a rear-view camera, commencement remove your vehicle's rear license plate and interior trunk panel. Using a power drill, punch a pocket-sized pigsty through the exposed license plate mounting area and run your photographic camera's ability and video string through it. Attach a bare wire ability cablevision to your camera's power connector, then strip your car's reverse light wires and splice them with your bare wire power cable. To learn how to mountain the rear-view camera and backup monitor, scroll down!

Did this summary assist you?

Thanks to all authors for creating a page that has been read 245,998 times.